5005H14 aluminum coil Mexico

Design Standard
Based on API 6D and customer requirements
Temperature Range
-150 to 428°F (-101 to 220°C)
NPS 1-36 (DN 25-900)
Pressure Rating
ASME 150 - ASME 2500
End Connections
RF, RTJ as per B16.5 &B16.47 BW, Butt Welded as per B16.25
Contact Now


5005H14 aluminum coil Mexico

Introduction of 5005H14 aluminum coil Mexico

chemical composition

Aluminum Al: margin

Silicon Si: ≤0.30

Copper Cu: ≤0.20

Magnesium Mg: 0.50~1.1

Zinc Zn: ≤0.25

Manganese Mn: ≤0.20

Chromium Cr: ≤0.10

Iron Fe: 0.000~0.700

Note: Single: ≤0.05; Total: ≤0.15

Applications: automotive fixtures, inspection fixtures, instrument shells, boats, gas pipes, refrigerator panels and appliances. 5005 is also used in building components, high-end curtain wall panels, and as an electrical conductor.

Can produce alloy thickness: 0.1-500mm Processing technology: hot rolling

Ordering method: customized production according to demand

Features of 5005H14 aluminum coil Mexico

This is a non-heat-treatable magnesium-containing aluminum alloy. Cold working strengthens (hardens) the alloy and is very good in terms of corrosion resistance and weldability.

Machinability is poor, especially under soft tempering conditions. It can be machined, but it is more difficult than many aluminum alloys. It is recommended to process under a hard temper, such as H34, H38.

The formability is very good.

This alloy is known for its excellent welding characteristics.

This alloy does not respond to heat treatment, except for annealing to reduce cold working strain.

The alloy is forgeable. Please consult the alloy supplier for the operating range temperature.

This alloy has excellent cold working characteristics, so hot working is usually not performed.

Excellent cold working conditions.

If required, it can be annealed at 650 F and then air cooled.

The purpose of 5005H14 aluminum coil Mexico

Typical use: aluminum coil for automotive inspection tools and fixtures

With the rapid development of the automotive industry over the years, accidents caused by quality problems occur frequently, so people's requirements for automotive quality control are also increasing. In the design of automobiles, more and more attention is paid to the safety and quality of automobiles, especially the effective quality inspection method of automobile inspection tools. Automobile inspection tools, aluminum alloy inspection tools, and fixtures are light in weight and easy to operate. Usually 5000 series and 6000 series products are used. 5005H14 aluminum coil Mexico is one of them.

5005H14 aluminum coil Mexico temper

The difference between 5005o state and 5005H14, 5005H24

The 5005o state is the softest, it is annealed and completely recrystallized, so it is the softest. The 5005H14 aluminum coil Mexico and 5005H24 have reached the semi-hard state in different ways. 5005H14 is work hardening, 5005H24 is annealing to ensure performance. Their strength indicators are basically the same, but the elongation rate is quite different. 5005H24 is greater than 5005H14, and 5005H24 can be understood relatively softly.

Recommended by 5005H14 aluminum coil Mexico manufacturer

Which 5005 aluminum plate manufacturer is better? Here is Mingtai Aluminum for you. Why do you recommend this manufacturer? The reasons are as follows:

5005 aluminum coil manufacturer is strong: Mingtai Aluminum has been established for more than 22 years, and its production base, production technology, sales method, business philosophy and other product-related content continue to be enriched. Its business scope covers more than 70 countries and regions around the world, and it has a large number of loyalty User.

Good sales service: One-stop service from pre-sale to after-sale, puts users in mind, provides users with high-quality products, and allows users to buy with confidence.